Available 24/7 at contact@steel-grades.com

Description

Germany AWS DIN 17440 (2001), DIN 17441 (1997), DIN 17455 (1985), DIN 17456 (1985), DIN 17457 (1985), DIN 17458 (1985), DIN 5512-3, DIN EN 10028-7, DIN EN 10088-1, DIN EN 10088-2, DIN EN 10088-3, DIN EN 10088-4, DIN EN 10088-5, DIN EN 10151, DIN EN 10216-5 (2004), DIN EN 10217-7, DIN EN 10222-5, DIN EN 10250-4, DIN EN 10253-3, DIN EN 10253-4, DIN EN 10263-5, DIN EN 10264-4 (2002), DIN EN 10269, DIN EN 10272, DIN EN 10296-2 (2005), DIN EN 10297-2 (2005), 1.4301 Specialsteel Stainless steels - Technical delivery conditions for drawn wire and Mechanical Properties, Chemical Element, Cross Reference, Datasheet.

Datasheet for: Steel Grades:Specialsteel: 1.4301
Category Class Grade Standard Country Application
Steel GradesSpecialsteel 1.4301 AWS Germany Stainless steels - Technical delivery conditions for drawn wire

Chemical composition(mass fraction)(wt.%) of the 1.4301

C Si Mn P S Cr Ni N
≤0.07 ≤1.00 ≤2.00 ≤0.045 ≤0.015 17.0 -19.0 8.00 -10.5 ≤0.11

Mechanical Properties of steel grade 1.4301

Yield
Rp0.2 (MPa)
Tensile
Rm (MPa)
Impact
KV/Ku (J)
Elongation
A (%)
Reduction in cross section on fracture
Z (%)
As-Heat-Treated Condition Brinell hardness (HBW)
394 (≥) 812 (≥) 41 43 31 Solution and Aging, Annealing, Ausaging, Q+T,etc 432

Physical Properties of steel grade 1.4301

Temperature
(°C)
Modulus of elasticity
(GPa)
Mean coefficient of thermal expansion 10-6/(°C) between 20(°C) and Thermal conductivity
(W/m·°C)
Specific thermal capacity
(J/kg·°C)
Specific electrical resistivity
(Ω mm²/m)
Density
(kg/dm³)
Poisson’s coefficient, ν
34 - -     0.41 -  
941 943 - 11.3 232   -  
915 - 34 32.2   224 442

Heat Treatment of steel grade 1.4301

Heat treated : 1421°C - 1732°C

Technological Curves of steel grade 1.4301

Cross Reference Table (Equivalent Grade) of 1.4301

Relevant standard of 1.4301

DIN 17440 (2001) Stainless steels - Technical delivery conditions for drawn wire DIN-17440-(2001).pdf
DIN 17441 (1997) Stainless steels - Technical delivery conditions for cold rolled strips and slit coils strip and sheets cut from such strips for pressure purposes DIN-17441-(1997).pdf
DIN 17455 (1985) Welded circular tubes of stainless steels for general requirements; technical delivery conditions DIN-17455-(1985).pdf
DIN 17456 (1985) Seamless circular tubes of stainless steels for general requirements; technical delivery conditions DIN-17456-(1985).pdf
DIN 17457 (1985) Welded circular tubes of austenitic stainless steels for special requirements; technical delivery conditions DIN-17457-(1985).pdf
DIN 17458 (1985) Seamless circular tubes of austenitic stainless steels for special requirements; technical delivery conditions DIN-17458-(1985).pdf
DIN 5512-3 Materials for rail vehicles - Steels - Part 3: Stainless steel flat products; Selected standard DIN-5512-3.pdf
DIN EN 10028-7 Flat products made of steels for pressure purposes - Part 7: Stainless steels DIN-EN-10028-7.pdf
DIN EN 10088-1 Stainless steels - Part 1: List of stainless steels DIN-EN-10088-1.pdf
DIN EN 10088-2 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes DIN-EN-10088-2.pdf
DIN EN 10088-3 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes DIN-EN-10088-3.pdf
DIN EN 10088-4 Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes DIN-EN-10088-4.pdf
DIN EN 10088-5 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes DIN-EN-10088-5.pdf
DIN EN 10151 Stainless steel strip for springs - Technical delivery conditions DIN-EN-10151.pdf
DIN EN 10216-5 (2004) Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes DIN-EN-10216-5-(2004).pdf
DIN EN 10217-7 Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes DIN-EN-10217-7.pdf
DIN EN 10222-5 Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels DIN-EN-10222-5.pdf
DIN EN 10250-4 Open die steel forgings for general engineering purposes - Part 4: Stainless steels DIN-EN-10250-4.pdf
DIN EN 10253-3 Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements DIN-EN-10253-3.pdf
DIN EN 10253-4 Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements DIN-EN-10253-4.pdf
DIN EN 10263-5 Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels DIN-EN-10263-5.pdf
DIN EN 10264-4 (2002) Steel wire and wire products - Steel wire for ropes - Part 4: Stainless steel wire DIN-EN-10264-4-(2002).pdf
DIN EN 10269 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties DIN-EN-10269.pdf
DIN EN 10272 Stainless steel bars for pressure purposes DIN-EN-10272.pdf
DIN EN 10296-2 (2005) Welded circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel DIN-EN-10296-2-(2005).pdf
DIN EN 10297-2 (2005) Seamless circular steel tubes for mechanical and general engineering purposes - Technical delivery conditions - Part 2: Stainless steel DIN-EN-10297-2-(2005).pdf

Available Suppliers

Our main peoducts of steel are many kinds of special steel, like tool steel, mould steel, alloy steel, alloy constructural steel, heat-resistant steel, high speed tool steel,spring steel and bearing steel , stainless steel and so on, which have formed 12 series and more than 350 varieties with n...

Rfq.: sales@longhaisteel.com
  • Do you supply this 1.4301?
  • List your company on S&G now? Join
  • Non-paying users only
Top